MarkChampion

XLS 2000, need to boost volume

Recommended Posts

I am using a guitar rig as a pre-amp into an XLS 2000. I would like to generate more volume to get the most out of the XLS. Do I have to have a mixer or is there another way?

The guitar set up is a TC Electronic Nova System (specs below) and a Boss Equalizer (which has a level control that provides some volume boost):

Guitar processor specs:

Max. Output Level

(Balanced/Unbalanced):

20 dBu/14 dBu, R-load = 1200 Ohm

20 dBu / 14 dBu / 8 dBu / 2 dBu

> 104 dB, 20 Hz to 20 kHz

<-98 dB (0.0013 %) @ 1 kHz

+0/-0.3 dB, 20 Hz to 20 kHz

I am playing live shows with limited set-up times so a mixer doesn't seem like a practical option. Thanks in advance for any suggestions.

Share this post


Link to post
Share on other sites
Deromax    0

Your processor appears to be able to provide enough output to drive the XLS to maximum power. Is there any gain or volume you can increase on the processor? Volume on the guitar istelf? Is the XLS gain at maximum? Are you using balanced TRS cables? Using the Drive input?

Adding another device should not be necessary and will increase the backgroud hiss even more.

Also, you should be patching the Boss pedal between the guitar and the TC unit, as typically the Boss are working at instrument level, not line level.

Share this post


Link to post
Share on other sites
dakos    0

In addition to what Deromax wrote and asked, I see on page 15 of the user manual of your processor that the gain of the unit is determined by three parameters, the output Range, the InGain and the BoostMax, so make sure these are set properly.

You have a great little combo just needs a little tweaking :)

Share this post


Link to post
Share on other sites
MI-9584    0

Get your guitar tech off his *beep* n tell him to put his AC voltmeter on the output of the EQ right at the amp input as you play so he can get an average level.This is REALLY where EQ belongs.I don't like the EQ loop deal.Usually too much noise!!Whatever you get here will determine how hard you are hitting the amp.If there is over 2.0Vac of signal and the amp will do full with this or close to it then ur o.k. If there is considerably more than you are considerably more O.K.If there is considerably less than ur not O.K. !!A gain stage(notice,I did not say pre-amp) may be required for you.Remember,The Nova is just a Stomp box,no matter how sophisticated,it's still a stomp box.You may need to be a little more exacting in the system you gig with.No diss to you meant,I love to mix good musicians and you are probably of a caliber that needs to be more demanding of the equipment!!There are quite a few good guitar pre's made and that may be a route you have to take.

Share this post


Link to post
Share on other sites
joust    0

As Avi says, verify the Output Range parameter in the Levels menu of the manual. Also, check the Advanced menu pages for explanations about the Boost function.

Enjoy!

Alain

Share this post


Link to post
Share on other sites
swiveltung    0

Seems a small mixer would not be difficult to setup. Maybe a 2 channel or 4 channel. Would give you more tone options too. The little Peavey (PV-6?) is good. Not sure if the 6 has them but the ones with more channels have amazingly good effects in them too and a USB output.

Share this post


Link to post
Share on other sites
dakos    0

The Peavey has a USB input and output which is a great feature to have if it was working properly, unfortunately it has allot of noise in it that makes it unusable, not allot of effects nor allot of tone options, just a basic mixer which could be used here but not needed.

Avi

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now