Search:     Advanced search
Glossary
Knowledge Base / Microphones / Questions about Crown microphone models / PZM microphones


Showing: 1-20 of 32    »»
Articles
 
document PZM-11LL signal level too low?
I'm recording the signal of a PZM-11LL line-level mic into a DVD recorder, but the recorded level seems low. What can I do? Lorn...
document Will PZM-185 mics work for audience miking?
I'm putting together a portable studio and am looking for a multi-use microphone to capture a stereo image of audience participation through...
document Where should I place PZM-11LL mics for voice recognition?
I'll be using a voice-recognition system in a room 12 ft x 30 ft long and 12 feet high with bare walls, ceiling and floor. Where should I place two...
document Do you have a wall-mount PZM for voice recognition?
Do you have a wall-mountable or wireless microphone that is suitable for use with a PC for voice recognition software? Tahlia Jayde,...
document How far can I mike a conference with the PZM-10?
The FAQs say the maximum distance mouth-to-mic for the PZM-10 is 3 feet. I need better than that because I am unable to sway folks from using ceiling...
document Where can I get information on discontinued PZM microphones?
I recently came into possession of some old Crown mics. One is a PZM-30GP, quite old, with the PX-T transformer. The other is a lavalier boundary...
document How can I mike a piano with a PZM without using tape?
I'd like to permanently mike a grand piano with a PZM, but I don't want to gaffer-tape the mic to the underside of the lid. Are there any other...
document Would wireless PZM-30D and PZM-185 mics work to record a conference?
We have several PZM-30D and PZM-185 mics, and are using them to record conferences. We are considering going wireless because the weight of the...
document Where to place a PZM-11LL to prevent picking up duct noise?
I am currently working on a psychology department tenant improvement of spaces studying child behavior. The ceilings are 9'6" above a finished...
document Should I use PZM-11 or PZM-11LL for voice recognition?
I’m installing a voice recognition system throughout a home that has been designed for an individual with cerebral palsy. I had intended to use...
document How far can a PZM-11LL mic be from the area I want to record voices from?
That depends on how reverberant or "live" the room acoustics are, and how loud the background noise is. The PZM-11LL can pick up speech...
document I want to use a PZM-11 or PZM-11LL with a VCR. What do I need to make the mic work?
The PZM-11 has a mic-level output. It requires: A small mixer with phantom power, such as made by Rolls. A mic cable between the mic and...
document How do I connect a PZM-185 or Sound Grabber II to my camcorder?
I recently purchased a Crown PZM-185 for use in videotaping classroom lessons.  In order to use the mic, do I have to connect it to my...
document Which PZM should I choose for drums?
I'm about to buy my first PZM mic and I'm wondering what mic to start with - I'm going to use it for drums... Can you guys help me choose a mic for...
document How do I wire a PZM-10LL to my mixer mic input?
I have a PZM-10LL mic and can't seem to figure out how to connect it to my mixer XLR mic input. Here is how I connected the PZM-10LL wires:...
document PZM-185 output level vs. Sound Grabber II output level
I used to have a Sound Grabber that I loved for its ability to pick up any sound (seemingly regardless of distance). When it finally failed I...
document How do I mount a PZM to a panel? Is a PZM waterproof?
I've acquired four PZM-30Ds which I intend to mount on 1-meter square plex panels to form a cube. I intend to first record some Texas thunderstorms...
document Have you a schematic for a PX-T phantom power adapter for an older PZM microphone?
Below is a sketch of the PX-T schematic. The PX-T converts 48V DC from phantom power into +/- 18V DC bipolar power. B+ goes to the PZM pin 2, B-...
document Sound Grabber II or PZM-185?
What's the difference between the two? I can see one has a 3.5mm" jack and the other is XLR - besides that, is there any...
document What is the wiring for old PZMs (PZM-30GP, PZM-31S, PZM-6S)?
I have a PZM-6S that had a three-pin XLR on it (looks like it was cut off). Is it possible to get the pin assignments?  Chris...


Powered by KnowledgebasePublisher (Knowledgebase software)