You may also be interested in the following product(s)
A culmination of nearly two decades of R&D in PWM and switch-mode amplification, DriveCore is a Crown exclusive that combines hundreds of parts into one chip the size of a your fingertip, resulting in more efficiencies and unsurpassed reliability. Learn more about DriveCore technology here: http://www.crownaudio.com/usa/drivecore.htm.
Analog & Digital Inputs
With digital audio transport via HARMAN’s proprietary BLU-Link, plus balanced analog inputs, DCi gives you a tremendous audio advantage – at a much lower cost. The priority input router allows you to specify a primary input, and if audio is lost the amp automatically switches to the other input.
Network Monitoring & Control
Better monitoring, control and audio manipulation with the HiQnet™ protocol that’s over standard TCP/IP. Remotely see how all networked DCi amplifiers are performing and control them as needed. In addition, this allows Audio Architect software and the Powered by Crown app to work with DCi amplifiers.
Programmable General Purpose Input/Output Ports
GPIO ports can be configured in many different ways, such as volume controls, recall presets, or to report errors to a master computer.
Digital Signal Processing
DSP capabilities include the following: LevelMAX Limiters, Input/Output EQ, Delay, Matrix Mixer, and Speaker Line Monitoring
Three-Year, No-Fault, Fully Transferable Warranty completely protects your investment and guarantees its specifications
|DUAL (all channels driven)||DUAL||BRIDGED (all channels driven)||BRIDGED|
|Frequency Response (8 Ohms, 20 Hz - 20kHz)||±0.25 dB|
|BLU Link Signal-to-Noise Ratio (ref. rated power, 8Ohms, 20 Hz - 20 kHz)||>108 dB|
|Analog Input Signal to Noise Ratio (ref. rated Power, 8Ohm, 20 Hz - 20kHz||>104 dB|
|Total Harmonic Distortion (at full rated power, 20Hz - 20kHz)||0.35%|
|Voltage Gain (at Maximum Level Setting)||34 dB|
|Damping Factor (20 Hz to 100 Hz)||>1000||>1000||>1000||>1000||>1000||>1000||>1500||>1500|
|Input Impedance (nominal balanced, unbalanced)||10 kOhms, 5 kOhms|
|Maximum Input Level before Compression (Low Gain Mode)||+20dBu|
|Load Impedance Stereo/Dual Mode||2 - 16 Ohms; 70Vrms and 100Vrms|
|Load Impedance Bridge Mono||4 - 16 Ohms; 140Vrms and 200Vrms|
|Cooling||Continuously variable speed forced air, front to back airflow|
|Maximum Fan Noise (re dBA SPL @ 1M)||45||45||47||45||45||47||47||47|
|Required AC Mains (±10%)||100V - 240V ~50/60Hz|
|IEC Power Connector||15A IEC||15A IEC||15A IEC||15A IEC||15A IEC||20A IEC||15A IEC||20A IEC|
|Width||19 in. (48.3cm)|
|Height||3.5 in. (8.75cm)|
|Depth||14.25 in (36.cm)||14.25 in (36.cm)||14.25 in (36.cm)||14.25 in (36.cm)||14.25 in (36.cm)||17 in (43.2 cm)||14.25 in (36.cm)||17 in (43.2 cm)|
|Weight||18.8 lbs (8.53kg)||20.1 lbs (9.12kg)||23.5 lbs (10.66kg)||18.8 lbs (8.53kg)||20.1 lbs (9.12kg)||30 lbs (13.6kg)||23.5 lbs (10.66kg)||30 lbs (13.60kg)|
Share your videos or photos of your DriveCore Install amps in action!