I would like someone to tell me how to connect my new I-Tech 6000 to my computer. Step by step...
THANKS!
1
How to connect my amp the first time?
Started by Li Producciones, Feb 28 2008 04:19 PM
6 replies to this topic
#2
DGlass
-
- Members
-
- 2,541 posts
.
Posted 28 February 2008 - 04:28 PM
You don't say if you are using IQwic or System Architect software so I will assume it is the IQwic software.
Try the System Technology Note STN005 "How to get started using TCP/IQ components." at: http://www.crownaudio.com/support/systems_...ogies_notes.htm
This should get you started with IQwic.
Try the System Technology Note STN005 "How to get started using TCP/IQ components." at: http://www.crownaudio.com/support/systems_...ogies_notes.htm
This should get you started with IQwic.
#4
Li Producciones
-
- Members
- 6 posts
Posted 28 February 2008 - 05:00 PM
I HAVE A PROBLEM!!!!
I tried to download the new firmware to the amp, and now it only says this: Loader v2, Network Upgrade, Awaiting TFTP.
What should I do????º
I tried to download the new firmware to the amp, and now it only says this: Loader v2, Network Upgrade, Awaiting TFTP.
What should I do????º
QUOTE(DGlass @ Feb 28 2008, 04:28 PM) 
You don't say if you are using IQwic or System Architect software so I will assume it is the IQwic software.
Try the System Technology Note STN005 "How to get started using TCP/IQ components." at: http://www.crownaudio.com/support/systems_...ogies_notes.htm
This should get you started with IQwic.
Try the System Technology Note STN005 "How to get started using TCP/IQ components." at: http://www.crownaudio.com/support/systems_...ogies_notes.htm
This should get you started with IQwic.
#5
DGlass
-
- Members
-
- 2,541 posts
.
Posted 28 February 2008 - 05:07 PM
QUOTE(Li Producciones @ Feb 28 2008, 05:00 PM)
I HAVE A PROBLEM!!!!
I tried to download the new firmware to the amp, and now it only says this: Loader v2, Network Upgrade, Awaiting TFTP.
What should I do????º
I tried to download the new firmware to the amp, and now it only says this: Loader v2, Network Upgrade, Awaiting TFTP.
What should I do????º
QUOTE(DGlass @ Feb 28 2008, 04:28 PM)
You don't say if you are using IQwic or System Architect software so I will assume it is the IQwic software.
Try the System Technology Note STN005 "How to get started using TCP/IQ components." at: http://www.crownaudio.com/support/systems_...ogies_notes.htm
This should get you started with IQwic.
Try the System Technology Note STN005 "How to get started using TCP/IQ components." at: http://www.crownaudio.com/support/systems_...ogies_notes.htm
This should get you started with IQwic.
Shut down the amp
On the back is a small reset hole. Using a small tool hold in the micro switch while powering up the amp.
wait for the Preset and data lights to go off and back on then remove the tool.
Open the TCP/IQ Utility program. The firmware version should show up with an LD extention.
Using TCP/IQutility program load in the Display firmware first.
Power down the amp and load in the the DSP firmware.
If you did this backwards you may not get the amp back and it may have to come in for service.
Power cycle the amp.
#6
Li Producciones
-
- Members
- 6 posts
Posted 28 February 2008 - 05:30 PM
I did a power cycle and when I connect the amp to the pc it tells me no firmware version.
Where and how can I do what you are telling me??
"Using TCP/IQutility program load in the Display firmware first.
Power down the amp and load in the the DSP firmware. "
????
SORRY FOR MY IGNORANCE, BUT I NEED THIS TO WORK IN FOUR HOURS
,
Shut down the amp
On the back is a small reset hole. Using a small tool hold in the micro switch while powering up the amp.
wait for the Preset and data lights to go off and back on then remove the tool.
Open the TCP/IQ Utility program. The firmware version should show up with an LD extention.
Using TCP/IQutility program load in the Display firmware first.
Power down the amp and load in the the DSP firmware.
If you did this backwards you may not get the amp back and it may have to come in for service.
Power cycle the amp.
Where and how can I do what you are telling me??
"Using TCP/IQutility program load in the Display firmware first.
Power down the amp and load in the the DSP firmware. "
????
SORRY FOR MY IGNORANCE, BUT I NEED THIS TO WORK IN FOUR HOURS
,
QUOTE(DGlass @ Feb 28 2008, 05:07 PM)
QUOTE(Li Producciones @ Feb 28 2008, 05:00 PM)
I HAVE A PROBLEM!!!!
I tried to download the new firmware to the amp, and now it only says this: Loader v2, Network Upgrade, Awaiting TFTP.
What should I do????º
I tried to download the new firmware to the amp, and now it only says this: Loader v2, Network Upgrade, Awaiting TFTP.
What should I do????º
QUOTE(DGlass @ Feb 28 2008, 04:28 PM)
You don't say if you are using IQwic or System Architect software so I will assume it is the IQwic software.
Try the System Technology Note STN005 "How to get started using TCP/IQ components." at: http://www.crownaudio.com/support/systems_...ogies_notes.htm
This should get you started with IQwic.
Try the System Technology Note STN005 "How to get started using TCP/IQ components." at: http://www.crownaudio.com/support/systems_...ogies_notes.htm
This should get you started with IQwic.
Shut down the amp
On the back is a small reset hole. Using a small tool hold in the micro switch while powering up the amp.
wait for the Preset and data lights to go off and back on then remove the tool.
Open the TCP/IQ Utility program. The firmware version should show up with an LD extention.
Using TCP/IQutility program load in the Display firmware first.
Power down the amp and load in the the DSP firmware.
If you did this backwards you may not get the amp back and it may have to come in for service.
Power cycle the amp.
#7
Li Producciones
-
- Members
- 6 posts
Posted 28 February 2008 - 09:14 PM
Thanks for everything.
I restored everything, and now I'm controlling the amp via Wi-Fi in my Mac using Windows Parallels!!!
Thanks for everything!
I restored everything, and now I'm controlling the amp via Wi-Fi in my Mac using Windows Parallels!!!
Thanks for everything!
QUOTE(Li Producciones @ Feb 28 2008, 05:30 PM)
I did a power cycle and when I connect the amp to the pc it tells me no firmware version.
Where and how can I do what you are telling me??
"Using TCP/IQutility program load in the Display firmware first.
Power down the amp and load in the the DSP firmware. "
????
SORRY FOR MY IGNORANCE, BUT I NEED THIS TO WORK IN FOUR HOURS
,
Shut down the amp
On the back is a small reset hole. Using a small tool hold in the micro switch while powering up the amp.
wait for the Preset and data lights to go off and back on then remove the tool.
Open the TCP/IQ Utility program. The firmware version should show up with an LD extention.
Using TCP/IQutility program load in the Display firmware first.
Power down the amp and load in the the DSP firmware.
If you did this backwards you may not get the amp back and it may have to come in for service.
Power cycle the amp.
Where and how can I do what you are telling me??
"Using TCP/IQutility program load in the Display firmware first.
Power down the amp and load in the the DSP firmware. "
????
SORRY FOR MY IGNORANCE, BUT I NEED THIS TO WORK IN FOUR HOURS
,
QUOTE(DGlass @ Feb 28 2008, 05:07 PM)
QUOTE(Li Producciones @ Feb 28 2008, 05:00 PM)
I HAVE A PROBLEM!!!!
I tried to download the new firmware to the amp, and now it only says this: Loader v2, Network Upgrade, Awaiting TFTP.
What should I do????º
I tried to download the new firmware to the amp, and now it only says this: Loader v2, Network Upgrade, Awaiting TFTP.
What should I do????º
QUOTE(DGlass @ Feb 28 2008, 04:28 PM)
You don't say if you are using IQwic or System Architect software so I will assume it is the IQwic software.
Try the System Technology Note STN005 "How to get started using TCP/IQ components." at: http://www.crownaudio.com/support/systems_...ogies_notes.htm
This should get you started with IQwic.
Try the System Technology Note STN005 "How to get started using TCP/IQ components." at: http://www.crownaudio.com/support/systems_...ogies_notes.htm
This should get you started with IQwic.
Shut down the amp
On the back is a small reset hole. Using a small tool hold in the micro switch while powering up the amp.
wait for the Preset and data lights to go off and back on then remove the tool.
Open the TCP/IQ Utility program. The firmware version should show up with an LD extention.
Using TCP/IQutility program load in the Display firmware first.
Power down the amp and load in the the DSP firmware.
If you did this backwards you may not get the amp back and it may have to come in for service.
Power cycle the amp.
