Hi @all
I use I-Tech with a different brand than JBL (...shame on me)
So my problem is, how can i set the gainstructure for my different system-outputīs?
Are the "dB"īs at the output-scale relative or weighted to "dBu"???
I have to gain the highīs and the midīs -8 dB ; the lowīs must be raise about 3 dB and the subīs need + 5 dB --- that are the controller-settings by the employer
So with an ashley or Bss- DSP i can set the Output-Gainīthe recommended levelīs , but how can i do this in the IQwic -software?
Maybe a stupid question, but i donīt find a answer.
Hope someone can help
Thanks
Adi
1
Gain structure
Started by Adi, May 11 2005 12:56 PM
5 replies to this topic
#2
martyb
-
- Members
- 1 posts
Posted 16 May 2005 - 10:30 PM
Adi The first Eq that you set in the filter settings will control the bandpass output... I found this out by mistake.. but try it!! Send a tone thru the amp and change the gain on the first filter you add.. Raise it up and down and you will see it controls the band pass output as needed.. Do I assume you have Eaw Kf730 from the boosts and cuts you have??? If so I can send you my wig files of the settings... But I assome no responsibility for the settings and would ask you to be sure of all required settings to make sure they are correct....
hope this helps
hope this helps
QUOTE(Adi @ May 11 2005, 12:56 PM)
Hi @all
I use I-Tech with a different brand than JBL (...shame on me)
So my problem is, how can i set the gainstructure for my different system-outputīs?
Are the "dB"īs at the output-scale relative or weighted to "dBu"???
I have to gain the highīs and the midīs -8 dB ; the lowīs must be raise about 3 dB and the subīs need + 5 dB --- that are the controller-settings by the employer
So with an ashley or Bss- DSP i can set the Output-Gainīthe recommended levelīs , but how can i do this in the IQwic -software?
Maybe a stupid question, but i donīt find a answer.
Hope someone can help
Thanks
Adi
I use I-Tech with a different brand than JBL (...shame on me)
So my problem is, how can i set the gainstructure for my different system-outputīs?
Are the "dB"īs at the output-scale relative or weighted to "dBu"???
I have to gain the highīs and the midīs -8 dB ; the lowīs must be raise about 3 dB and the subīs need + 5 dB --- that are the controller-settings by the employer
So with an ashley or Bss- DSP i can set the Output-Gainīthe recommended levelīs , but how can i do this in the IQwic -software?
Maybe a stupid question, but i donīt find a answer.
Hope someone can help
Thanks
Adi
#3
Adi
-
- Members
- 4 posts
Posted 17 May 2005 - 01:06 PM
Yes Marty,
wrote you a PM on this @ a different forum
thx
Adi
wrote you a PM on this @ a different forum
thx
Adi
#4
Bradford Benn
-
- Admin
-
- 1,025 posts
Power User
Posted 17 May 2005 - 01:45 PM
As Martyb pointed out, you can use the gain control on a high pass or low pass filter to do this exact feature. For more information about how to do this in the software there is an Application Guide for I-Tech available on the page http://www.crownaudio.com/amp_htm/itech.htm
#5
Adi
-
- Members
- 4 posts
Posted 18 May 2005 - 12:12 PM
Thanks Brad for your reply!
I download the .pdf and have now something to read.
I let you know, if there are still questions
thx
Adi
I download the .pdf and have now something to read.
I let you know, if there are still questions
thx
Adi
#6
paultucci
-
- Members
- 8 posts
Posted 06 June 2005 - 09:59 PM
Adi,
In firmware version 1.3 there is a new channel gain control available. I believe the range is +/- 24 dB. That is what we are using for a bandwidth level control. It's the only spot I found to gain gain rather than trimming the other bandwidths back.
Channel 1 (or 2) Gain is what it is called in the pulldown menu.
Tucci
In firmware version 1.3 there is a new channel gain control available. I believe the range is +/- 24 dB. That is what we are using for a bandwidth level control. It's the only spot I found to gain gain rather than trimming the other bandwidths back.
Channel 1 (or 2) Gain is what it is called in the pulldown menu.
Tucci
