We have a PZM-6D installed in the piano at church; someone recently pulled the cable out of the XLR connector. I would like to re-solder the wires to the circuit board inside the connector, but I can't find a wiring diagram. The microphone cable has a red conductor, a white conductor and a shield. The circuit board has three connections points, the left most is where the shield was connected, but I can't tell where the other conductors were connected. Can I get a diagram showing the wiring terminations?
1
PZM-6D Wiring
Started by David@PUMC, Feb 09 2009 10:07 PM
4 replies to this topic
#2
DGlass
-
- Members
-
- 2,541 posts
.
Posted 12 February 2009 - 08:20 AM
Attached is a wiring diagram for the wire to the board in the connector.
My apologies for the size of the picture that was the best I could do after cutting it out of the document.
My apologies for the size of the picture that was the best I could do after cutting it out of the document.
Attached Files
-
PZM_6Dwiring.bmp 65.13K
8 downloads
-
PZM_6Dwiring.JPG 3.8K
8 downloads
#3
David@PUMC
-
- Members
- 3 posts
Posted 12 February 2009 - 10:27 PM
QUOTE(DGlass @ Feb 12 2009, 08:20 AM) 
Attached is a wiring diagram for the wire to the board in the connector.
My apologies for the size of the picture that was the best I could do after cutting it out of the document.
My apologies for the size of the picture that was the best I could do after cutting it out of the document.
Thanks for the reply,
I can't read the text on the picture you attached, I think that I could make out that the white wire and the shield were the two outside connections and the red wire is the center connection. Is this correct? I can identify where the shield was terminated so if you can tell which wire to connect to the center pin I will have all the information I need to make the repair.
#4
DGlass
-
- Members
-
- 2,541 posts
.
Posted 13 February 2009 - 08:36 AM
PZM_6Dwiring.pdf 73.05K
12 downloadsQUOTE(David@PUMC @ Feb 12 2009, 10:27 PM)
QUOTE(DGlass @ Feb 12 2009, 08:20 AM)
Attached is a wiring diagram for the wire to the board in the connector.
My apologies for the size of the picture that was the best I could do after cutting it out of the document.
My apologies for the size of the picture that was the best I could do after cutting it out of the document.
Thanks for the reply,
I can't read the text on the picture you attached, I think that I could make out that the white wire and the shield were the two outside connections and the red wire is the center connection. Is this correct? I can identify where the shield was terminated so if you can tell which wire to connect to the center pin I will have all the information I need to make the repair.
I was able to get that section of the document blown up and saved as a .pdf. Let me try and repost it.
PZM_6Dwiring.pdf 73.05K
12 downloads
Attached Files
-
PZM_6Dwiring.JPG 43.67K
0 downloads
#5
David@PUMC
-
- Members
- 3 posts
Posted 13 February 2009 - 01:31 PM
QUOTE(DGlass @ Feb 13 2009, 08:36 AM)
PZM_6Dwiring.pdf 73.05K
12 downloadsQUOTE(David@PUMC @ Feb 12 2009, 10:27 PM)
QUOTE(DGlass @ Feb 12 2009, 08:20 AM)
Attached is a wiring diagram for the wire to the board in the connector.
My apologies for the size of the picture that was the best I could do after cutting it out of the document.
My apologies for the size of the picture that was the best I could do after cutting it out of the document.
Thanks for the reply,
I can't read the text on the picture you attached, I think that I could make out that the white wire and the shield were the two outside connections and the red wire is the center connection. Is this correct? I can identify where the shield was terminated so if you can tell which wire to connect to the center pin I will have all the information I need to make the repair.
I was able to get that section of the document blown up and saved as a .pdf. Let me try and repost it.
PZM_6Dwiring.pdf 73.05K
12 downloadsThanks again for your help. This is exactly what I needed.
