amedeo bruni

Crown DC 300a - lighted rocker switch

10 posts in this topic

Hello everybody.

I'm from Italy, and I'm looking for a replacement of the red lighted rocker switch of my beloved DC-300a.

I've been looking at it for ages, asked everybody here in Italy, and visited countless on-line stores, but unsuccessfully.

If someone here can help me, with info where to find it, please please contact me or post here. If someone has to sell, me one, used or spare, it would be great as well.

Of course, I'll be willing to pay all the asked money to get one.

Thank you so much.

Amedeo Bruni

amedeo.bruni@hotmail.com

Share this post


Link to post
Share on other sites

I am sorry to say the manufacture of the switch stop making it many years ago. :( We do carry a replacement non-lighted version that is available from our Parts Department here at Crown. :) the non-lighted replacement part number is M20020-0 and comes with an instructions for wiring the replacement style switch.

Crown Parts can be reached by contacting bprice@crownintl or by phone at 1.574.294.8210 .

You could probably also order it from the Crown distributor for Italy:

Audio Equipment SRL

Via Solferino 52

Monza 20052 Italy

PH: 39-0- 39-212-221

FAX: 39-0-39-214-0011

Share this post


Link to post
Share on other sites
Hello everybody.

I'm from Italy, and I'm looking for a replacement of the red lighted rocker switch of my beloved DC-300a. 

I've been looking at it for ages, asked everybody here in Italy, and visited countless on-line stores, but unsuccessfully.

If someone here can help me, with info where to find it, please please contact me or post here. If someone has to sell, me one, used or spare, it would be great as well.

Of course, I'll be willing to pay all the asked money to get one.

Thank you so much.

Amedeo Bruni

amedeo.bruni@hotmail.com

2119[/snapback]

Hi Amedeo, I too had a 300A with a dead power light. This may be more trouble than you are willing to go to, however I was able to disassemble the switch and replace the lamp. Small neon job from Radio Shack. I drilled out the switch retainers, soldered in the new lamp and it's as good as new. I used small screws and nuts to hold the switch halfs together. I LOVE my 300A. Not the most powerful Crown I own but for home audio it has done it's job for me for over 20 years.

PLEASE disconnect power prior to attempting this repair :o

Share this post


Link to post
Share on other sites
Hi Amedeo,  I too had a 300A with a dead power light.  This may be more trouble than you are willing to go to, however I was able to disassemble the switch and replace the lamp.  Small neon job from Radio Shack.  I drilled out the switch retainers, soldered in the new lamp and it's as good as new.  I used small screws and nuts to hold the switch halfs together.  I LOVE my 300A.  Not the most powerful Crown I own but for home audio it has done it's job for me for over 20 years. 

PLEASE disconnect power prior to attempting this repair  :o

2176[/snapback]

Thank you, Bob.

I always try to keep things as original as possible, so I'd have considered to rebuild the original switch, but this time seems almost impossible, since the lower part of the switch (where the light is housed) has melted!

But I'll be very happy if you can tell me what kind of 'small neon' lamp have you used to replace the burned one (please keep in mind here in Italy we do not have Radio Shack).

Thanks again.

Share this post


Link to post
Share on other sites
Hi Amedeo,  I too had a 300A with a dead power light.  This may be more trouble than you are willing to go to, however I was able to disassemble the switch and replace the lamp.  Small neon job from Radio Shack.  I drilled out the switch retainers, soldered in the new lamp and it's as good as new.  I used small screws and nuts to hold the switch halfs together.  I LOVE my 300A.  Not the most powerful Crown I own but for home audio it has done it's job for me for over 20 years. 

PLEASE disconnect power prior to attempting this repair  :o

2176[/snapback]

Thank you, Bob.

I always try to keep things as original as possible, so I'd have considered to rebuild the original switch, but this time seems almost impossible, since the lower part of the switch (where the light is housed) has melted!

But I'll be very happy if you can tell me what kind of 'small neon' lamp have you used to replace the burned one (please keep in mind here in Italy we do not have Radio Shack).

Thanks again.

2193[/snapback]

Hi Amedeo,

Sorry to hear that the switch housing is fried. Makes me think something shorted in the switch as the power bulb does not run hot. You could order one of the new switches from crown, David posted that pn above, and try to install a light in the new one. However the new switch is not lit and the rocker probably will not have the red lens in the middle. I have not seen one. You may be able to use your old rocker with a neon or LED in the switch. Radio Shack pn 272-704 is a 120v panel mount neon lamp that you can break open to get the bulb. I think you are 220v so a different value resistor would be required. If you go LED, which would sure be a longer lasting fix, you will need to find some low voltage DC to drive the lamp through the current limiting resistor. One more thought, I think the switch was made by Levitron with a part number stamped into the metal attaching ears. I know David said that it was no longer available, but you might check with them. Good luck!!

Share this post


Link to post
Share on other sites

Hi Amedeo,  I too had a 300A with a dead power light.  This may be more trouble than you are willing to go to, however I was able to disassemble the switch and replace the lamp.  Small neon job from Radio Shack.  I drilled out the switch retainers, soldered in the new lamp and it's as good as new.  I used small screws and nuts to hold the switch halfs together.  I LOVE my 300A.  Not the most powerful Crown I own but for home audio it has done it's job for me for over 20 years.  

PLEASE disconnect power prior to attempting this repair  :o

2176[/snapback]

Thank you, Bob.

I always try to keep things as original as possible, so I'd have considered to rebuild the original switch, but this time seems almost impossible, since the lower part of the switch (where the light is housed) has melted!

But I'll be very happy if you can tell me what kind of 'small neon' lamp have you used to replace the burned one (please keep in mind here in Italy we do not have Radio Shack).

Thanks again.

2193[/snapback]

Hi Amedeo,

Sorry to hear that the switch housing is fried. Makes me think something shorted in the switch as the power bulb does not run hot. You could order one of the new switches from crown, David posted that pn above, and try to install a light in the new one. However the new switch is not lit and the rocker probably will not have the red lens in the middle. I have not seen one. You may be able to use your old rocker with a neon or LED in the switch. Radio Shack pn 272-704 is a 120v panel mount neon lamp that you can break open to get the bulb. I think you are 220v so a different value resistor would be required. If you go LED, which would sure be a longer lasting fix, you will need to find some low voltage DC to drive the lamp through the current limiting resistor. One more thought, I think the switch was made by Levitron with a part number stamped into the metal attaching ears. I know David said that it was no longer available, but you might check with them. Good luck!!

2207[/snapback]

The replacement switch is solid black, no clear or red window or even a place to put a lamp. :(

Share this post


Link to post
Share on other sites

Thank you very much, guys.

Your help has been much appreciated.

I'll try to rebuild someway the fried parts and get a new light, since the red lens are mint.

Amedeo

Share this post


Link to post
Share on other sites

Well, now I am in need of the same switch.

I expect I will see the same frustrations as I seek a replacement everywhere I can think of.

I could just get the plain black switch and be done with it, but this DC 300A is going in a rack with two others and it just wouldn't really look right.

I'll let you know if I find a good substitute.

Share this post


Link to post
Share on other sites

One more suggestion. When I had the switch apart replacing the lamp I noticed that the switch contacts were becoming pitted due to startup current surge. Putting the unit on an external switch i.e. power strip, will save the switch from further damage. If new ones were available this would not be an issue. But they apparently are not :(

Share this post


Link to post
Share on other sites

You might try www.alliedelec.com they have a good selection of lighted rectangular power switches. :)

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!


Register a new account

Sign in

Already have an account? Sign in here.


Sign In Now