|
| 2Ω Stereo (per ch.) |
700W |
1000W |
1600W |
3000W |
| 4Ω Stereo (per ch.) |
500W |
800W |
1200W |
2100W |
| 8Ω Stereo (per ch.) |
275W |
475W |
650W |
1200W |
| 8Ω Bridge-Mono |
1000W |
1600W |
2400W |
4200W |
| 4Ω Bridge-Mono |
1400W |
2000W |
3200W |
6000W |
XTi
There's no debate – when you choose Crown's XTi 2 Series, you're choosing one of the most powerful and innovative amplifiers on the market today. That's because the all-new XTi 2 Series amps continue to set the standard for unmatched performance and value, delivering the goods night after night without breaking a sweat.
|
- Peakx Plus™ Limiters provide the ultimate in system
performance and protection by allowing full control over
threshold, attack, and release
- Enhanced Subharmonic Synth section provides user control
over frequency, gain and filter type for system-specific tuning
- 3 User-defined fan mode controls – normal, early and fullspeed
– for matching fan performance to a specific application
- New system monitoring provides software visibility of AC
line voltage and power supply temperature
- Integrated cast-aluminum handles for easy handling
and enhanced durability
- Locking power cord clip provides a secure connection
between the amplifier and power cord
- Updated HiQnet System Architect™ control software
- Increased number of presets to a total of 50; 49 of which are user definable
Input EQ
|
6 parametric filters per channel
with adjustable Q, ±15 dB boost/cut. Also
adjustable high and low shelving filters. This
8-filter EQ section can be bypassed.
|
Crossover Filters |
Highpass and Lowpass
per channel. Butterworth 6/12/18/24 dB
per octave. Linkwitz-Riley 24/48 dB per
Octave. Also includes ± 15 dB bandpass
gain and polarity control. |
Output EQ |
8 parametric filters per channel
with adjustable Q, ±15 dB boost/cut.
This 8-filter EQ section can be bypassed. |
Delay |
For signal alignment of driver;
50 mS of total delay. |
SubHarmonic Synth |
Takes the low-frequency
content of the input signal and "synthesizes"
a new signal that is the same as the input
signal but one octave lower. The new
synthesized signal is then mixed with the
original signal to create the effect. New:
Users now have control over frequency,
gain, and filter type. |
Peakx™ Plus Limiter |
User defeatable limiter
that allows users to control Threshold,
Attack, and Release times.
|
Presets |
50 total presets, 49 of which
are user-definable. |
Sensitivity (for full rated power at
4 ohms)
|
1.4 Vrms
|
Frequency Response (at 1 watt, 20 Hz - 20 kHz) |
+0 dB, –1 dB |
Signal-to-Noise Ratio (below rated 1kHz power at 8 ohms) |
XTi1002/2002/4002: 100 dB (A weighted)
XTi6002: 103 dB (A weighted) |
Total Harmonic Distortion (THD) |
< 0.5% |
Damping Factor 20 Hz to 1 kHz |
> 500 |
Crosstalk (below rated power) |
20 kHz - 1 kHz: > 70 db
|
Input Impedance (nominal) |
20k ohms balanced, 10k ohms unbalanced |
Maximum Input Signal |
+22 dBu typical |
AC Line Voltage and Frequency Configurations |
100 VAC, 120 VAC, 220-240 VAC 50/60 Hz |
AC Line Current
(120 VAC amplifier playing
1/8 power pink noise into 4 ohms per ch) |
XTi1002: 6.8A; no more than 38W at idle
XTi2002: 8.3A; no more than 38W at idle
XTi4002: 10.5A; no more than 38W at idle
XTi6002: 15.3A; no more than 180W at idle |
Operating Temperature |
0°C to 40°C at 95% relative humidity
(non-condensing) |
Level
|
Two front-panel rotary level controls, one for each channel
|
Power Switch |
On/Off switch applies AC power to the amplifier |
Sel/Prev/Next Buttons |
Three buttons near the LCD screen that are used to access menu items and front panel lockout |
LCD Screen |
Backlit liquid crystal display that shows preset and processing status |
Signal Indicator
|
Green LED, one per
channel, illuminates when a very low-level
signal is present at input (may be used for
troubleshooting cable runs).
|
–10 Indicator |
Green LED flashes when output
signal exceeds -10 dB below clip. |
–20 Indicator |
Green LED flashes when output
signal level exceeds -20 dB below clip. |
Ready Indicator |
Green LED, one per channel,
illuminates when the amplifier is ready to
produce audio. |
Clip Indicator |
Red LED, one per channel, turns on at the threshold of audible distortion |
Temp Indicator |
Red LED, one per channel, illuminates under excessive temperature conditions
|
Power Indicator |
Blue LED illuminates when the amplifier has been turned on and has power |
Input Connectors |
XLR, one per channel
|
Link/Out Connector |
Loop-thru signal from
input connector for linking another
amplifier, one per channel. |
Output Connectors |
Two Neutrik® Speakon®
NL4MP output connectors. Channel-1
Speakon® is wired with Ch. 1 and Ch.
2 outputs for use with optional single
4-conductor cable. Two binding post outputs
(in parallel with Speakon® connectors). |
HiQnet™ USB Connector |
Type B, connects to
HiQnet™ network. |
Chassis |
Steel
|
Front Panel |
Cast-aluminum |
Cooling |
Proportional speed fan with
front-to-rear airflow. |
Dimensions |
XTi 1002/2002/4002: 19" (W) x 3.5" (H)
x 12.25" (D)
XTi 6002: 19" (W) x 3.5" (H) x 16.2" (D) |
Net Weight |
XTi 1002/2002/4002: 18.5 lbs (8.4kg)
XTi 6002: 24.0 lbs (10.9kg) |
Shipping Weight |
XTi 1002/2002/4002: 21.5 lbs (9.8kg)
XTi 6002: 30.0 lbs (13.6kg)
|
|
|
